Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 1 of 11 PageID #: 33642
`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 1 of 11 PagelD #: 33642
`
`EXHIBIT 14
`EXHIBIT 14
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 2 of 11 PageID #: 33643
`
`CATERPILLAR®
`
`Press Release
`
`For Worldwide Release November 2016
`Updated from Jit1v 2016 version
`
`Caterpillar Introduces the PM620 and PM622 Cold Planers
`
`Caterpillar Inc is pleased to announce the availability of the PM620 and PM622 Cold Planers The
`
`machines are high production highly maneuverable half lane milling machine that perform
`
`controlled full depth removal of asphalt and concrete pavements in a single pass Operating weight
`for the PM620 is approximately 33 330 kg 73260 lb and the PM622 is approximately 33 900 kg
`for the PM620 is approximately 29 400 kg 64680 lb and the
`74580 lbs Transport weight
`PM620 is approximately 30 000 kg 66140 lb
`
`Engine
`The PM620 and PM622 are powered by a Cat® C18 ACERT TM
`engine a turbocharged 6 cylinder
`diesel engine that provides 470 kW 630 hp of gross power The C18 engine meets regional
`the engines meet US EPA Tier 4 Final EU Stage
`Stage DIA equivalent and
`
`IV emission standards For all other regions the engine meets Tier 3
`
`emission requirements In regions that require it
`
`China Nonroad Stage ifi emission standards The engine is isomounted to reduce vibration and
`
`increase operator comfort
`
`The Automatic Engine Speed Control feature allows the engine to optimize output to match the load
`
`reducing excessive fuel consumption and wear on the engine
`
`The turbocharged airtoair aftercooling system provides high horsepower with increased response
`
`time while keeping exhaust temperatures low which generates significant
`
`improvements in airflow
`
`This increases efficiency and reduces emissions
`
`The cooling system provides cool
`
`intake air in order to maximize fuel efficiency and minimize
`
`emissions An on demand variable speed fan draws ambient air from the top of the engine hood and
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`TRIAL EXHIBIT
`Ex 3365
`
`Case No CA No 17770JDW
`
`CAT 770041686
`Ex
`33650001
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 3 of 11 PageID #: 33644
`
`through the cooling package keeping the engine compartment cool Heated air exits from the rear of
`
`the machine directed away from the operators station for greater operator comfort
`
`Undercarriage and Drive System
`
`The PM620 and PM622 utilize a four post design The leg posts feature an auto leveling function
`
`that provides smooth height adjustment without stepping
`
`The machines are fully hydrostatically driven by two variable displacement propel pumps supplying
`
`oil to variable displacement motors on each track Drive motors are piston type and automatically
`
`control displacement
`job site A propel
`
`to provide maximum torque for work or greater speed for moving around the
`
`leversteering joystick provides infinite control of the travel speed within the
`
`range
`
`The machines have a robust propel system with a diagonal cross flow design that provides
`
`exceptional
`
`traction The pumps drive opposing track motors front to back and side to side to
`
`ensure the machine has power across the center of gravity of the machine In extreme conditions
`
`automatic traction control minimizes slippage by providing more power to tracks that grip
`
`There are several automated functions to simplify operation The operators platform has a hold
`
`button to stop the machine and pause various functions while making truck interchanges or job stops
`
`It returns to previous working speed and functions when deactivated There is a speed limit to allow
`
`the operating speed to set to ensure consistent operations The machines are equipped with position
`
`sensing cylinders in the posts and hydraulic systems providing basic machine function
`
`improvements such as service height
`
`indications and rear leg auto stop It also enables the optional
`
`Cat Grade Control system to include additional capabilities
`
`The drive tracks are based on durable proven Caterpillar designs and components Track tension
`automatically adjusts to ensure optimum operation Track assemblies are 1788 mm 704 long 305
`mm 12 wide and feature replaceable bolt on polyurethane track pads for long service life
`
`Fourmode steering is standard An electronic control module processes inputs from the sensors on
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041687
`Ex
`33650002
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 4 of 11 PageID #: 33645
`
`the front and rear tracks along with input from the steering selector controls It provides precise
`
`simultaneous track movement
`
`in the crab and coordinated steering modes and automatically realigns
`
`the rear tracks to center when the front tracks only steering mode is selected In the coordinated
`mode the inside turning radius is a tight 200 m 6 5 providing exceptional maneuverability in
`
`confined spaces
`
`A true tracking alignment function provides greater steering precision smoother cornering and
`
`reduced track wear This function makes small adjustments to the alignment of individual
`
`tracks to
`
`ensure that the tracks are travelling in the optimal direction to make the desired maneuver without
`
`dragging a track or shorting a radius This extends track pad and undercarriage component
`
`life
`
`Operators Environment
`
`The operators station features dual operating controls including joystick steeringpropel lever
`
`upper conveyor controls and rear track steering controls Ergonomic instrumentation layout has been
`designed for comfort and ease of use A touchscreen display is visible in day or night conditions and
`
`keypads are backlit for comfortable low light operation Keypad controls are positioned within easy
`reach for the operator A large storage locker is standard Options that add comfort for the operator
`
`include suspension seats and a hydraulically operated canopy The canopy can quickly deploy and
`
`retract to a storage position without disrupting operation The canopy can be equipped with optional
`
`front and rear windscreens that protect the entire width of the operator station
`
`The touchscreen display provides easy to read gauges function indicators and warning indicators to
`
`keep the operator informed of machine operation and vital systems It also displays video from the
`
`optional
`
`remote cameras if equipped An optional second display can provide an additional monitor
`
`for machine functions
`
`The computerized monitoring system includes several electronic control modules ECMs that
`constantly monitor system pressures and engine conditions with multiple modes of operation The
`
`system can provide self diagnostics and fault codes to the touchscreen display
`
`The machines are equipped with excellent perimeter lighting for enhanced low light operation The
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041688
`Ex
`33650003
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 5 of 11 PageID #: 33646
`
`halogen lights are positioned around the machine to provide light to work areas An upgrade to LED
`
`lights is available The operators platform has floor lighting that activates upon button press from
`
`any control station to provide visibility when accessing the machine in low light conditions
`
`An optional
`
`remote camera system is available The cameras are positioned to provide the operator
`
`with views to the front andor rear of the machine Video is displayed on the primary touchscreen
`
`Up to two optional magnetic mounting cameras are available
`
`Cutting System
`
`The cutting chamber features a design that streamlines material flow reduces wear on the chamber
`
`and has enhanced flush cutting capability Side plates move via independent hydraulic cylinders that
`
`are equipped with position sensors This ensures that the side plates float at the proper level and
`eliminates binding It also eliminates the need for a wire yoyo sensor by enabling the entire length
`of the side plate to function as an averaging ski for grade matching A hydraulically operated anti
`
`slab device prevents slabbing of the road surface It also protects the collecting conveyor and ensures
`
`an optimum discharge opening to the rotor chamber The chamber also features a right side hinged
`
`door to provide service access to the rotor The moldboard side plates and anti slab device all
`
`feature raise lower float and hold functions
`
`The rotor drive system features a dry clutch driving a planetary gear reducer an efficient and reliable
`
`system of applying rotor power to the pavement The clutch is coupled to the engine and is
`
`hydraulically actuated by the keypad controls on the operators console Three cutting speeds are
`available to match the best rotor RPM and torque with the job site conditions and are controlled
`
`electronically
`
`from the keypad on the operators control console
`
`Automatic Load Control is a standard feature to enhance machine productivity while milling An
`ECM continually evaluates engine rpm and controls propel speed as required to maintain peak
`performance for maximum output
`
`Two five rib high tensilestrength belts drive the rotor through a drum drive gear reducer The
`
`hydraulically powered automatic drive belt tensioner prevents slipping and reduces maintenance
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041689
`Ex
`33650004
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 6 of 11 PageID #: 33647
`
`The PM620 is equipped with a 2010 mm 79 wide high production rotor and the PM622 is
`equipped with a 2235 mm 88 wide high production rotor The maximum cutting depth is 330 mm
`13 The rotor is equipped with durable threepiece quick release tool holders and carbide tipped
`cutting bits arranged in a chevron pattern for maximum breakout force Optional Cat Diamond Bits
`
`are available for greater cutting performance during certain applications
`
`The quick release conical
`
`tool holders feature a tapered fit maintaining tightness in the holder base
`
`The mandrel
`
`features large replaceable carbide faced loading paddles to effectively move milled
`
`material onto the collecting conveyor
`
`resulting in higher production and less wear on the inside of
`
`the rotor chamber and cutting tools Triple tree cutting bit placements on rotor end cutters provides
`
`optimum bit spacing to clean up loose material and reduces wear on drum when maneuvering in the
`
`cut
`
`Optional Cat Diamond Bits offer the ultimate in cutting performance The bits last up to 80 times
`
`longer than conventional carbide bits extending periods between stops for bit maintenance This
`
`increases production and reduces operating costs by facilitating more uptime and reducing the need
`
`to purchase and store pallets of carbide bits Cat Diamond Bits are sharper than conventional carbide
`
`bits reducing drag on the cutting system and allowing the machine to cut at faster speeds increasing
`
`production Reduced drag also decreases fuel consumption vibration to the operator and machine
`
`wear which lowers operating and maintenance costs
`
`Cat Grade Control Option
`The PM620 and PM622 can be equipped with integrated Cat Grade Control The 2Dcapable3D
`
`ready grade and slope system automatically controls rotor depth and cross slope to a preset cutting
`
`depth and can be enhanced for full 3D control with the addition of optional equipment The base
`
`system is fully integrated with the machine providing easier more precise operation and better
`
`system protection The system can be configured with contacting or non contacting grade sensors
`
`including Cat sonic sensors and mounting hardware the side plate position or optional
`
`inboard ski
`
`The machine can be set up to control grade on both sides using any combination of sensors Or the
`
`machine can be set up to control grade on one side of the machine and slope on the other The
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041690
`Ex
`33650005
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 7 of 11 PageID #: 33648
`
`system allows you to change the sensor arrangement during operation with simple commands as
`
`work site application requires
`
`The position sensing technology coupled with the Cat Grade Control system provides the machine
`
`with functions such as an automatic plunge cut
`
`feature that eases the rotor into the start of the cut
`
`The machines also have a ramp in ramp out capability to provide a gradual sloped entry or exit
`
`from the cut An auto jump feature allows the machine to exit a cut clear an obstacle such as a
`
`manhole cover or grate and reenter the cut at the previously set depth with use of a single button
`
`A cross communication function allows the operator to view and change settings of control boxes
`
`located on the opposite side of the machine This provides the operators with a means to control both
`
`sides of a job from a single location The system also provides a cross coupling function that when
`
`an adjustment
`
`is made to the grade or slope of one side of the machine the opposite side will
`
`automatically adjust based on the command parameters Continual
`
`readout for rotor depth and
`
`cross slope is displayed on each control box and is visible in light or dark conditions
`
`Sonic grade control sensors can be easily positioned on each side and provide a consistent accuracy
`
`to ± 3 mm 18
`
`Conveyor System
`
`is driven by a high torque hydraulic motor to ensure maximum efficiency
`The collecting conveyor
`A large chamber discharge opening clears out the cutter box quickly to maintain high production
`The seamless collector belt features 32 mm 125 high cleats and is 850 mm 335 wide to clear
`fine particles An optional grease tensioning system uses a
`out the cutter box effectively and control
`
`grease cylinder to adjust tension and tracking on the belt rather than an adjustable screw The
`cylinder makes the adjustment easier and reduces crew exposure to the spinning belt A traditional
`
`screw adjustment design is also available
`
`A standard water spray system lubricates the conveyor belt and helps control dust A centrifugal
`
`pump supplies water to spray nozzles in the cutting chamber The nozzles focus water spray in a flat
`
`fan pattern to the rotor for better cooling of cutting bits Nozzles are easily removed for inspection
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041691
`Ex
`33650006
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 8 of 11 PageID #: 33649
`
`and replacement without tools The system features an automatic function that operates only when
`
`the rotor is engaged and machine is moving forward which conserves water The system is triple
`
`filtered and includes a gauge to monitor water pressure a low water level
`control valves to conserve water usage An onboard winterization system is also included providing
`
`indicator and water
`
`a simple method to purge waterlines with pressurized air
`
`The 3400 L 898 gal water tank can be filled from standard wide fill openings on the top of the
`
`machine or the standard ground level port at the rear of the machine There is also an optional side
`fill port This enables adding water while the machine is operating An optional water transfer pump
`
`is available to facilitate additional
`
`filling options
`
`An additional water spray system can be fitted as an option for greater lubrication cooling and dust
`
`reduction during heavyduty applications This system includes an additional water pump a second
`
`spray bar located in the rotor chamber housing and extra spray nozzles on the collecting conveyor
`
`The hydraulically controlled front loading conveyor features height adjustment for raise and lower
`
`and two cylinders for a 60 degree swing to the left and right of center that can be controlled from the
`
`operators station or at two ground level control stations It
`
`is equipped with upper aluminum covers
`
`for added protection against material spills and blowing of fine materials The loading conveyor can
`
`also be hydraulically folded downwards reducing machine dimensions during transportation
`
`The seamless loading conveyor belt features 32 mm 125 high cleats and is 850 mm 335 wide
`It offers long service life and excellent control of fine particles Variable belt speed provides
`
`adjustable control of the loading conveyor to ensure proper discharge
`
`An optional dust abatement system is available The system utilizes a vacuum that pulls dust from
`
`the collecting conveyor and the transitional zone between the collecting and loading conveyors The
`
`dust is ejected through the loading conveyor along with the discharge material
`
`Optional Equipment
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041692
`Ex
`33650007
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 9 of 11 PageID #: 33650
`
`Options include a diamond bit cutting drum and bits a selfpowered canopy canopy windscreens
`
`additional
`
`touchscreen displays Cat Grade Control inboard averaging ski with position sensing
`
`cylinder suspension seats remote cameras additional water spray system dust abatement vacuum
`
`system a rotor turning attachment
`
`a highpressure wash down system bucket
`
`trays for cutter bit
`
`bucket storage a high capacity water tank refilling pump and an electric refueling pump
`
`Serviceability
`
`Large doors open wide to provide excellent access to the engine emissions package air filter
`
`hydraulic components and daily service points
`
`The computerized monitoring system includes Electronic Control Modules ECMs that continually
`monitor system pressures and engine conditions with multiple modes of operation The system can
`
`provide self diagnostics and provide fault code to the touchscreen display
`
`The machines feature long service intervals to reduce owning and operating costs Engine oil service
`
`is every 500 hours and hydraulic oil service is every 3000 hours if oil sampling is not conducted up
`
`to 6000 hours if scheduled oil sampling occurs
`
`An auxiliary electric pump drive provides an emergency hydraulic flow that allows a disabled
`machine to manage some machine functions and be towed away from the work area to ensure that
`
`the disabled machine will not disrupt
`
`the continuation of work
`
`The hydraulic rotor service door opens wide for convenient access to rotor for inspection and tool
`
`maintenance The engine mounted air compressor and cutting bit removal
`cutting tools quick and easy An optional rotor turning attachment
`
`tools make changing
`
`is available to turn the rotor
`
`during cutter bit replacement
`
`Hydraulic hoses are held neatly in place with polyurethane routing blocks The blocks separate hoses
`
`helping ensure that they do not rub on one another to provide long life and high reliability
`
`Wiring for the electrical system is protected by nylonbraided wrap Allweather connectors ensure
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041693
`Ex
`33650008
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 10 of 11 PageID #: 33651
`
`electrical system integrity Electrical wiring is colorcoded numbered and labeled with component
`
`identifiers to simplify troubleshooting
`
`Product LinkTM provides accurate timely and useful
`
`information about
`
`the location utilization and
`
`condition of your equipment The system streamlines diagnostic efforts maintenance scheduling
`
`and costs by providing communication flow of vital machine data and location information between
`
`the dealer and customer Optional configurations are available
`
`Two maintenance free Cat batteries that are specifically designed for maximum cranking power and
`
`protection against vibration provide the 24 volt electrical system The batteries are located at the rear
`
`of the machine and are easily accessible at ground level
`
`Other features that simplify service include leak resistant 0 ring face seal hydraulic fittings grouped
`
`quick connect hydraulic test ports scheduled oil sampling ports visual sight gauges and remote
`
`grease points
`
`For more information on the new PM620 and PM622 Cold Planers contact your Cat dealer
`
`Note to Editors Caterpillar rolls out products and services in each of its territories at different
`time intervals Although every effort is made to ensure that product
`information is released only
`after Caterpillar has received confirmation from our dealer network our plants and our
`marketing subsidiaries that products and services are available in the relevant region editors are
`kindly requested to verify with their local dealer for product availability and specifications
`
`CAT CATERPILLAR their respective logos Caterpillar Yellow and the Power Edge trade
`identity used herein are trademarks of Caterpillar and
`dress as well as corporate and product
`may not be used without permission
`
`VisionLink is a trademark of Trimble Navigation Limited registered in the United States and in
`other countries
`
`©2016 Caterpillar All Rights Reserved
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041694
`Ex
`33650009
`
`

`

`Case 1:17-cv-00770-JDW Document 369-14 Filed 04/12/24 Page 11 of 11 PageID #: 33652
`
`10
`
`Press Inquiries
`
`Caterpillar Trade Press Media Representatives
`
`Americas
`Sharon Holling HoRing Sharon Lrcatcom
`Johanna Kelly Kelly Johanna Lic4catcom
`
`Europe Africa Middle East
`Francine Shore Shore Francine Mcatcom
`
`Reader Requests
`
`wwwcatcomrequestCatinfo
`
`HIGHLY CONFIDENTIAL OUTSIDE ATTORNEYS EYES ONLY
`
`CAT 770041695
`Ex
`33650010
`
`