Palladiom Shading System
`Lutron Palladiom Motorized Roller Shades are
`ideal for exposed applications. Controlled by
`an ultra-quiet, precision Sivoia QS Palladiom
`drive, these shades are mounted on solid
`aluminum brackets that completely conceal
`wiring and offer a refined aesthetic in a variety
`of finishes to match any setting.
`
`085560g 1 04.23.20
`
`Features
`• Single shades up to 12 ft (3.66 m) wide
`• Single shades up to 12 ft (3.66 m) tall
`• Symmetrical light gaps, as small as 1⁄2 in (12 mm)
`NOTE: At high aspect ratio (tall and narrow) shade sizes, Lutron
`may apply a fabric deduction, which increases the size of the light
`gaps to compensate for the increased probability of telescoping
`• Shades move in unison, maintaining alignment within 1⁄8 in (3 mm) at
`all times
`• Sound: 35 dBA measured 3 ft (0.91 m) from the EDU
`• Bottom bar speed: 3.6 in/sec (91.4 mm/sec)
`• Solid aluminum shade brackets with concealed fasteners, available
`in a variety of finishes
`• Ideally paired with the Palladiom Bottom Rail, available in
`matching finishes
`• Available with a wide variety of fabric types, including sheer,
`translucent, and room darkening fabrics
`• Power failure memory for the lifetime of the product
`• Available in QS Wired and QS Wireless configurations
`• Designed to provide a means to completely conceal wiring and
`control/programming buttons
` – Control/programming buttons are easily accessed behind the
`finishing ring on the drive bracket (for details, see Finishing
`Rings on page 8)
`• Idler can be extended 1⁄8 in (3 mm) to allow for installation tolerance.
`Extending the idler increases the bracket-to-bracket width of the
`shade, as well as the light gap on the idler side of the shade.
`
`Power and Communication
`• Compatible power sources
` – Individual Plug-In
` › QSPS-P1-1-35V
` › QSPS-P2-1-35V
` › QSPS-P3-1-35V
` – 10-Output Power Panels
` › QSPS-10PNL
` › QSPSY-10PNL
` – Configurable Power Panels
` › QSPS-10PNL-NPM (with WIN-PS-5CC-R installed)
` › QSPS-30PNL-NPM (with WIN-PS-5CC-R installed)
` – Individual Junction Box
` › QSPS-J-1-35V
`• Low-voltage power and communication in a single
`4-wire cable
`• The connector provided with the shade is compatible with
`16-24 AWG solid or stranded wire (when using the wire housing
`WIN-WM-BOX-10, stranded wire is recommended due to its
`greater flexibility)
`
`Accessories
`• Wire management kit to help eliminate exposed wiring
`• Bracket shims for each bracket type
`
`IMPORTANT: Palladiom shades must be mounted to
`blocking or other suitable structural material. It is the
`responsibility of the installer to choose and install fasteners
`that are appropriate for the mounting surface such that each
`shade bracket can support 400 lbs (181 kg). For shades
`not in the Palladiom shade family, please contact Lutron for
`mounting guidelines.
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`GeigTech East Bay LLC Ex. 2048
` U.S. Patent No. 10,294,171
`
`

`

`Specifications
`
`Low Voltage Power
`• Operating voltage: Class 2, 35 V-
`• Power supply offers overvoltage protection (+/-10% of line voltage)
`for all devices in the system
`• Power supply provides appropriate Electrostatic Discharge (ESD)
`protection for all devices in the system
`• Power failure protection: Programming will not be lost if power is
`lost to the drive
`• Power must be derived from a Lutron NEC® Class 2 power source
`
`Flexible Configuration
`• Digitally assign and reassign shades to controls, groups,
`and scenes
`• Adjust limits locally via controls on the EDU
`• Remotely adjust limits and grouping of QS shades via wired
`controls or system (HomeWorks QS, myRoom, Quantum)
`• Remotely adjust limits and grouping of QS Wireless shades via
`system (HomeWorks QS, Radio RA 2, RA 2 Select, Caséta PRO)
`• No wired relays or wired group controllers required
`
`System Capacity
`• Standalone QS configuration supports 100 QS devices
`• Standalone QS configuration supports 100 QS zones
`
`Environment
`• Temperature: 32° - 104° F (0° - 40° C)
`• Humidity: 0% - 90%, non-condensing
`
`085560g 2 04.23.20
`
`Precision Control
`• Preset positions can be easily programmed at any point between
`the open and close limits
`• Shades stop within 1⁄8 in (3 mm) of programmed open, close, and
`preset positions
`• Intelligent Hembar Alignment (IHA): Shades remain within 1⁄8 in
`(3 mm) alignment when stopped or moving
`
`Controls
`• QS shades and controls in a system are wired together on the
`same communications link
`• QS shades are compatible with HomeWorks QS, myRoom, and
`Quantum control systems
`• QS Wireless shades are compatible with HomeWorks QS,
`RadioRA 2, RA 2 Select, and Caséta PRO control systems
`• Shades can be controlled by built-in shade columns on a GRAFIK
`Eye QS, or by low-voltage seeTouch QS keypads
`• Shades can be controlled using a Pico or 4-Group Remote Control
`• Shades can be controlled by Radio Window sensors when installed
`as part of a HomeWorks QS or Quantum system
`
`Integration
`• EDUs seamlessly integrate with Lutron lighting controls
`• Contact closure, RS232, and Ethernet available to integrate
`with A/V equipment such as timeclocks, security systems, and
`touch screens
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Dimensions
`
`Bracket-to-Bracket Width
`
`085560g 3 04.23.20
`
`Installed Shade
`Wall Mount (outside mount)
`
`Bracket-to-Bracket Width
`
`0.50 in
`(12 mm)
`
`Fabric width
`
`0.50 in
`(12 mm)
`
`Measurements & Deductions
`Bracket-to-Bracket Width Deductions
`• Outside-mount shades: no deduction
`• Inside-mount single and 2-shade systems: 1⁄16 in (1.6 mm)
`• Inside-mount systems with 3 or more shades:
`1⁄16 in (1.6 mm) deduction applies only to first and last shade
`
`First Shade:
`1⁄16 in (1.6 mm) deduction
`
`Intermediate Shade(s):
`no deduction
`
`Last Shade:
`1⁄16 in (1.6 mm) deduction
`
`Example: Inside-Mount Multi-Shade System
`
`Fabric Deductions
`• Lutron may apply fabric deductions to tall, narrow shades
` – Maximum fabric deduction of 1⁄4 in (6 mm) per side, resulting in a
`light gap of 3⁄4 in (19 mm) per side
` – Fabric deduction does not reveal
`a bare shade tube; Palladiom
`shades feature a finished sleeve
`that matches the bracket to
`provide a clean appearance
`
`No Fabric Deduction
`
`1⁄2 in
`(12 mm)
`light gap
`
`Max. Fabric Deduction
`
`3⁄4 in
`(19 mm)
`light gap
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Shade Options
`Mounting Options
`
`085560g 4 04.23.20
`
`Drive Side Options
`
`Left Side
`
`Right Side
`
`Inside Mount
`
`Outside Mount
`
`Fabric Drop Options
`
`Bottom Bar Options
`
`Regular Roll
`
`Reverse Roll
`
`NOTE: Reverse roll is recommended for dual-sided fabric, otherwise the shade
`roll will be a different color than the hanging fabric.
`
`1.
`
`2.
`
`3.
`
`4.
`
`5.
`
`1. Palladiom Bottom Rail*
`2. Half-Wrap Architectural Bottom Bar with Metal Endcaps**
`3. Half-Wrap Architectural Bottom Bar with Plastic Endcaps
`4. Designer
`5. Sealed (available in 3⁄16 x 1 in [5 x 25 mm] or 7⁄16 x 1 3⁄8 [11 x 35 mm])
`
`* Finishes available:
`• Pure White
`• Clear Anodized
`• Black Anodized
`• Satin Nickel
`
`** Finishes available:
`• Pure White
`• Clear Anodized
`• Black Anodized
`• Satin Nickel
`
`• Brass
`• Satin Graphite
`• Opal White
`
`NOTE: The bottom bar may be ordered in different finish than brackets.
`For more information about finishes, colors, and other design options,
`please visit: lutron.com/en-US/Products/Pages/ShadingSystems/
`PalladiomShades/DesignOptions.aspx
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Mounting Options - End Brackets
`Palladiom mounting brackets and accessories are made from solid aluminum and are available in 8 standard finishes
`(see the Bracket, Shim, & Accessory Finish Guide on page 10)
`NOTE: Brackets may be ordered in different finish than bottom bar
`• Aesthetic enhancements for clean, finished appearance (see the section titled ‘Aesthetic Enhancements’)
`• Shims (1 included with each bracket) can be used to level the shade (ceiling mount) or increase projection (wall mount)
`
`085560g 5 04.23.20
`
`Standard End Bracket
`Maximum fabric roll-up:
` 3 in (76 mm)
`
`Wall Mount
`
`3.00 in (76 mm)
`
`1.45 in
`(37 mm)
`
`Ceiling Mount
`
`2.00 in (51 mm)
`
`1.45 in
`(37 mm)
`
`2.00 in
`(51 mm)
`
`3.00 in
`(76 mm)
`
`WIN-BRK-LWC-FINISH CODE
`
`Extended End Bracket
`Maximum fabric roll-up:
` 3 1⁄2 in (89 mm)
`
`Wall Mount
`
`3.25 in (83 mm)
`
`1.45 in
`(37 mm)
`
`Ceiling Mount
`
`2.00 in (51 mm)
`
`1.45 in
`(37 mm)
`
`2.00 in
`(51 mm)
`
`3.25 in
`(83 mm)
`
`WIN-BRK-LWCE-FINISH CODE
`
`End Bracket Shim For use with all end brackets; sold separately in packs of 10
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Mounting Options - Center Brackets
`Palladiom mounting brackets and accessories are made from solid aluminum and are available in 8 standard finishes
`(see the Bracket, Shim, & Accessory Finish Guide on page 10)
`NOTE: Brackets may be ordered in different finish than bottom bar
`• Aesthetic enhancements for clean, finished appearance (see the section titled ‘Aesthetic Enhancements’)
`• Shims (1 included with each bracket) can be used to level the shade (ceiling mount) or increase projection (wall mount)
`
`085560g 6 04.23.20
`
`Standard Center Bracket
`Wall Mount
`Maximum fabric roll-up:
` 3 in (76 mm)
`
`Ceiling Mount
`
`3.00 in (76 mm)
`
`1.90 in
`(48 mm)
`
`2.00 in (51 mm)
`
`1.90 in
`(48 mm)
`
`2.00 in
`(51 mm)
`
`3.00 in
`(76 mm)
`
`WIN-BRK-LT-FINISH CODE
`(1) bracket supports 2 shades
`(shades are not coupled)
`
`Extended Center Bracket
`Maximum fabric roll-up:
` 3 1⁄2 in (89 mm)
`
`Wall Mount
`
`Ceiling Mount
`
`3.25 in (83 mm)
`
`1.90 in
`(48 mm)
`
`2.00 in (51 mm)
`
`1.90 in
`(48 mm)
`
`2.00 in
`(51 mm)
`
`3.25 in
`(83 mm)
`
`WIN-BRK-LTE-FINISH CODE
`(1) bracket supports 2 shades
`(shades are not coupled)
`
`Center Bracket Shim For use with all center brackets; sold separately in packs of 10
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Mounting Options - Jamb Bracket
`Palladiom mounting brackets and accessories are made from solid aluminum and are available in 8 standard finishes
`(see the Bracket, Shim, & Accessory Finish Guide on page 10)
`NOTE: Brackets may be ordered in different finish than bottom bar
`• Aesthetic enhancements for clean, finished appearance (see the section titled ‘Aesthetic Enhancements’)
`• Shims (1 included with each bracket) can be used to adjust the fit of the shade between the window jambs
`
`085560g 7 04.23.20
`
`Jamb Bracket
`Maximum fabric roll-up:
` 3 1⁄2 in (89 mm)
`
`Inside Mount
`
`Preferred orientation:
`
`Alternate orientation:
`
`Window
`
`2.00 in
`(51 mm)
`
`WIN-BRK-LJ-FINISH CODE
`
`NOTE: Use the flat edge as a reference to orient and mount the jamb bracket square to the window.
`
`1.86 in (47 mm)
`
`Jamb Bracket Shim Sold separately in packs of 10
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Aesthetic Enhancements
`
`085560g 8 04.23.20
`
`Concealed Wiring
`Bracket-integrated power connection combines with in-wall wire management accessories (details on page 11), for fully-concealed wiring
`
`Wire passage
`inside bracket
`
`Finishing Rings
`Each bracket includes a finishing ring in matching finish (center bracket includes 2), to conceal the bracket-shade interface
`(see the Bracket, Shim, & Accessory Finish Guide on page 10)
`
`Screw Covers
`Each bracket includes a screw cover in matching finish (not applicable to jamb bracket; center bracket includes 2)
`(see the Bracket, Shim, & Accessory Finish Guide on page 10)
`
`Matching screw cover
`slides on to conceal
`fastener heads
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Optional Aesthetic Enhancements
`
`085560g 9 04.23.20
`
`Decorative Covers
`Optional decorative covers fit over mounted brackets,* offering a prominent aesthetic which covers the edge of the fabric roll.
`* Available only on standard brackets. For decorative cover applications with extended brackets, please contact Lutron.
`
`For End Brackets
`
`See the Bracket, Shim,
`& Accessory Finish
`Guide on page 10)
`
`1.57 in
`(40 mm)
`
`1.30 in
`(33 mm)
`
`3.50 in (90 mm)
`
`3.00 in
`(76 mm)
`
`NOTE: Decorative Covers for End Brackets add 0.25 in (6.35 mm) at each end, beyond the bracket-to-bracket width. When using Decorative Covers with End Brackets
`for inside-mount applications, deduct 0.5 in (12.7 mm) from the bracket-to-bracket width to allow clearance for the Decorative Covers within the window opening.
`
`For Center Brackets
`
`See the Bracket, Shim,
`& Accessory Finish
`Guide on page 10)
`
`0.875 in
`(22 mm)
`
`1.90 in
`(48 mm)
`
`0.875 in
`(22 mm)
`
`3.00 in (76 mm)
`
`3.00 in
`(76 mm)
`
`3.50 in
`(90 mm)
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Bracket, Shim, and Accessory Finish Guide
`
`085560g 10 04.23.20
`
`End Bracket,
`Standard
`3˝ roll-up limit
`End Bracket,
`Extended
`3.5˝ roll-up limit
`Center Bracket,
`Standard
`3˝ roll-up limit
`Center Bracket,
`Extended
`3.5˝ roll-up limit
`
`Jamb Bracket
`3.5˝ roll-up limit
`
`Finishing Ring
`
`Screw Cover,
`End
`
`Screw Cover,
`Center
`
`Decorative Cover,
`End
`
`Decorative Cover,
`Center
`
`Recommended
`Shim Pack
`Packs of 10
`
`Pure White
`PWH
`
`Clear Anodized
`CLA
`
`Black Anodized
`BLA
`
`Satin Nickel
`SN
`
`Brass
`BRS
`
`Satin Graphite
`SGT
`
`Opal White
`OWH
`
`WIN-BRK-LWC-PWH
`
`WIN-BRK-LWC-CLA
`
`WIN-BRK-LWC-BLA
`
`WIN-BRK-LWC-SN
`
`WIN-BRK-LWC-BRS
`
`WIN-BRK-LWC-SGT
`
`WIN-BRK-LWC-OWH
`
`WIN-BRK-LWCE-PWH
`
`WIN-BRK-LWCE-CLA
`
`WIN-BRK-LWCE-BLA
`
`WIN-BRK-LWCE-SN
`
`WIN-BRK-LWCE-BRS
`
`WIN-BRK-LWCE-SGT
`
`WIN-BRK-LWCE-OWH
`
`WIN-BRK-LT-PWH
`
`WIN-BRK-LT-CLA
`
`WIN-BRK-LT-BLA
`
`WIN-BRK-LT-SN
`
`WIN-BRK-LT-BRS
`
`WIN-BRK-LT-SGT
`
`WIN-BRK-LT-OWH
`
`WIN-BRK-LTE-PWH
`
`WIN-BRK-LTE-CLA
`
`WIN-BRK-LTE-BLA
`
`WIN-BRK-LTE-SN
`
`WIN-BRK-LTE- BRS
`
`WIN-BRK-LTE-SGT
`
`WIN-BRK-LTE-OWH
`
`WIN-BRK-LJ-PWH
`
`WIN-BRK-LJ-CLA
`
`WIN-BRK-LJ-BLA
`
`WIN-BRK-LJ-SN
`
`WIN-BRK-LJ-BRS
`
`WIN-BRK-LJ-SGT
`
`WIN-BRK-LJ-OWH
`
`WIN-RING-PWH
`
`WIN-RING-CLA
`
`WIN-RING-BLA
`
`WIN-RING-SN
`
`WIN-RING-BRS
`
`WIN-RING-SGT
`
`WIN-RING-OWH
`
`WIN-BC-LWC-PWH
`
`WIN-BC-LWC-CLA
`
`WIN-BC-LWC-BLA
`
`WIN-BC-LWC-SN
`
`WIN-BC-LWC-BRS
`
`WIN-BC-LWC-SGT
`
`WIN-BC-LWC-OWH
`
`WIN-BC-LT-PWH
`
`WIN-BC-LT-CLA
`
`WIN-BC-LT-BLA
`
`WIN-BC-LT-SN
`
`WIN-BC-LT-BRS
`
`WIN-BC-LT-SGT
`
`WIN-BC-LT-OWH
`
`WIN-BRK-LV-PWH
`
`WIN-BRK-LV-CLA
`
`WIN-BRK-LV-BLA
`
`WIN-BRK-LV-SN
`
`WIN-BRK-LV2-PWH
`
`WIN-BRK-LV2-CLA
`
`WIN-BRK-LV2-BLA
`
`WIN-BRK-LV2-SN
`
`End:
`WIN-SHIM-LWC-PWH
`Center:
`WIN-SHIM-LT-PWH
`Jamb:
`WIN-SHIM-LJ-PWH
`
`End:
`WIN-SHIM-LWC-CLA
`Center:
`WIN-SHIM-LT-CLA
`Jamb:
`WIN-SHIM-LJ-CLA
`
`End:
`WIN-SHIM-LWC-BLA
`Center:
`WIN-SHIM-LT-BLA
`Jamb:
`WIN-SHIM-LJ-BLA
`
`End:
`WIN-SHIM-LWC-CLA
`Center:
`WIN-SHIM-LT-CLA
`Jamb:
`WIN-SHIM-LJ-CLA
`
`End:
`WIN-SHIM-LWC-BRS
`Center:
`WIN-SHIM-LT-BRS
`Jamb:
`WIN-SHIM-LJ-BRS
`
`End:
`WIN-SHIM-LWC-BLA
`Center:
`WIN-SHIM-LT-BLA
`Jamb:
`WIN-SHIM-LJ-BLA
`
`End:
`WIN-SHIM-LWC-PWH
`Center:
`WIN-SHIM-LT-PWH
`Jamb:
`WIN-SHIM-LJ-PWH
`
`For more information about finishes, colors, and other design options, please visit:
`lutron.com/en-US/Products/Pages/ShadingSystems/PalladiomShades/DesignOptions.aspx
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`

`

`Wire Management
`
`085560g 11 04.23.20
`
`Wire Housing
`Wire housing for installation inside wall or trim secures, protects, and allows access to the shade’s electrical connection. Can be
`installed beneath the bracket or concealed using the Spackle Ring and Plug.
`
`1.20 in
`(30.5 mm)
`
`0.62 in
`(16 mm)
`
`Package of 10:
`WIN-WM-BOX-10
`
`3.50 in (89 mm)
`
`0.78 in
`(20 mm)
`
`Spackle Ring & Plug
`Preserves clean wire entry during wall finishing, and provides bite for spackle in the transition area.
`Lutron recommends positioning the spackle ring behind the fabric roll, (if conditions allow), to maintain a clean aesthetic.
`
`1.00 in
`(25 mm)
`
`Package of 10 rings, 10 plugs:
`WIN-WM-SR-10
`
`3.50 in (89 mm)
`
`Lutron, The Lutron Logo, Palladiom, Caséta, GRAFIK Eye, HomeWorks, myRoom, Quantum, seeTouch, and Sivoia are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the U.S. and/or other countries.
`
`Palladiom Shading System
`
`Exposed Motorized Shade
`
`Job Name:
`
`S P E C I F I C AT I O N S U B M I T TA L
`Model Numbers:
`
`Page
`
`Job Number:
`
`